Service Details

  • Home
  • Service Details

Pedometer final inspection:


To inspect pedometer for keeping track of your steps and health monitoring onsite inline, our QC checks will verify the below quality points to make sure the products are acceptable, and send you a full inspection report in 24hrs after the inspection:

  • Aesthetic, visual defects, workmanship, surface and function inspections
  • On-site safety, regulation & function tests
  • Measurements & sizes checks
  • Quantity & assortment checks
  • Labels, markings, logos & barcodes quality inspections
  • Product specs, and special requirements verifying
  • Packaging, safety and drop tests onsite

The AQL QC inspections for pedometers are mostly called:

Pedometer final inspection

Please find below for a sample factory QC check points for pedometers:

ON-SITE INSPECTION CHECK LIST COMMENTS RESULT
Check all accessories with the item. -The item should not be missing any parts and all items should perform their functions properly. -II PASSED
Perform an internal check. -Take a photo to show all that the item contains all the components specified by the client. Also make a list of all of the item’s main electrical parts. A. Internal wiring shall be routed to provide sufficient creepage and clearance distances, avoid being trapped and be free from damage to the insulation.B. All screws shall be present, fully tightened with no damage
to the heads and anti tamper screws used as appropriate.
Request at least one picture to show the whole construction of product. -S1
N/A
- Function test:
1/ Power ON/OFF function test
2/Led indicator light function test
3/ Other function test claimed on gift box and
instruction manual-should not have malfunction
PASSED
- Check vibration and sound:-in normal mode
(time mode) push Reset and Start buttons
together . You will hear a sound. Next turn
swith on the downside to the vibration mode.
And push Reset and Start buttons together
one more time. You will feel vibration.-II
PASSED
Perform an endurance/life test--S1 PASSED
Polarity check & battery fitness check with batteries -
A.Voltage check if battery included: please write down the detail of findings, percentage failed, range of findings etc.
B. check the charge and discharge time of the baterry and ensure the rated energy stored is correct.
C. Check the battery is out of date or not- Report the battery production date (or expired date) or take the picture which can shows the date.
D. Check plastic strip that prevent the battery to discharge is whether exist or not if applicable
Please write down all results of this check (i.e. percentage failed, range of results, etc.).-S1
PASSED
Perform a barcode scanning test. -The barcode should be scannable and have the correct number. -S2 PASSED
Check plastic strip that prevent the battery to discharge is whether exist or not if applicable-II PASSED
Perform a rub test and adhesive test for all markings, logos, printing & labels found.-Rub the rating label for 15 seconds with water, then for 15 seconds with petroleum spirits. If petroleum spirits is not available, use alcohol. Use 3M tape for the adhesive test on the silk-screening and painting.-S1 PASSED
Perform a carton drop test: 10 drops from the correct height based on carton weight as defined in ISTA 1 A(6 faces, 3 edges,1 corner) - On 3 cartons – packed products should not get damaged PASSED
Test the battery compartment.-Make sure the correct battery size for the item can fit in the item’s battery compartment. -S1 PASSED
Perform a fatigue test for all adjustable parts. -Do this 20 times.- S1 N/A
Perform a stability test -On a surface inclined to 10 or 15 degrees. The item should not tip over.Please take clear picture to show that the product is in the most unfavourable position on the inclined plane. (If applicable) -S1 PASSED

3rd party preshipment products goods factory onsite inline Random AQL PSI TPI FRI DUPRO third party on-site in-line pre-shipment QA QC check quality control assurance services in China India Vietnam Thailand Malaysia Bangladesh Taiwan.

 

Menu
x