Service Details
- Home
- Service Details
Most Chinaware like saucers disks, plates, bowls, cups, mugs, vases etc. are made in Chaozhou Guangdong China. The onsite quality inspections of Saucers will normally be checked as below:
INSPECTION CHECKPOINTS | RESULTS | COMMENTS |
---|---|---|
Labels, markings, logos & barcodes quality inspections | OK | |
Aesthetic, visual defects, workmanship, surface and function checks | OK | |
Product specs, and special requirements inspections | OK | |
Packaging, safety and drop tests onsite | OK | |
Measurements & sizes checks | OK | |
On-site safety, regulation & function tests | NOT OK | |
Quantity & assortment verifying | N/A |
For third party quality inspection services, the technical classifications are as below:
The Saucers inspection checkpoints:
ONSITE INSPECTION LIST | COMMENTS | RESULT |
---|---|---|
Hand washing test -- --Wash the product with cotton fabric in cold water of room temperature (about 20--35degree) and hot water of tempertature (about 80 -- 90 degree) -- During washing, dip product into the water and wiping the whole surface of the product -No color should be removed from the item’s surface during the test and no printing, markings or paint should fade.-3 pcs | PASSED | |
Perform a fatigue test-On all adjustable parts. Do this 20 times.-S2 | PASSED | |
If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-S2 |
PASSED | |
Perform a fitting test check-The lid should fit the base well.-II | PASSED | |
Test the item for water leakage during the entire inspection period.-Fill the item with water then place onto a paper to check there is no leakage at all.-S2 | PASSED | |
Compare the inspection sample with the approval sample.-II | PASSED | |
Test the fit of the lid. and lid can not falls off when the teapot is tilted toward 90 degrees-If the item has a lid - The lid should fit well.-S3 | N/A | |
Test the strength of the handle.--S2 | PASSED | |
Perform a wobble test on a flat glass panel. Check both the top rim of the glass and the bottom.-There should be no wobbling of the base or the rim.-I | PASSED | |
Check capacity (volume) by weighing the item or by using a capacity gauge ( the mug, bowl and the container claimed with the volumn)-The results must conform with the specifications.-S2 | N/A | |
Check if items stand properly when pieces are stacked up, if this test fail, please state the cause clearly on inspection report and take photos- 1)Stack the products (60 pieces for the plate/reference and 12 pieces for bowl/reference and cup/reference ); 2) Ensure they can stack properly and do not wobble or tilt over-S2 |
N/A |
saucers on-site inspection services, saucers third party on-site inspection services in China, China saucers on-site inspection services, saucers third party on-site inspection in China, saucers on-site inspection services in China, saucers on-site inspection in China, saucers 3rd party on-site inspection, saucers 3rd party on-site inspection in China, China saucers on-site inspection, China saucers 3rd party on-site inspection services, saucers 3rd party on-site inspection services in China, China saucers third party on-site inspection services, saucers third party on-site inspection, saucers 3rd party on-site inspection services, saucers third party on-site inspection services, China saucers 3rd party on-site inspection, China saucers third party on-site inspection
3rd party preshipment products goods factory onsite inline final Random AQL PSI TPI FRI DUPRO third party in-line pre-shipment QA QC check quality control assurance services in China India Vietnam Thailand Malaysia Bangladesh Taiwan.