Service Details
- Home
- Service Details
Most Chinaware like disks, plates, bowls, cups, mugs, vases etc. are made in Chaozhou Guangdong China. The onsite quality inspections of Chinaware will normally be inspected as follows:
INSPECTION CHECKPOINTS | RESULTS | COMMENTS |
---|---|---|
A. Quantity inspection | OK | |
B. Shipping marks & packing | NOT OK | |
C. Labels, logos and colors | OK | |
D. Styles & measurements | N/A | |
E. Onsite safety and function tests | NOT OK | |
F. Special requirements | OK | |
G. AQL workmanship (Visual defects) |
OK |
For professional third party inspection services, the technical classifications are as below:
The Chinaware inspection checkpoints:
ONSITE CHECK LIST | COMMENTS | RESULT |
---|---|---|
If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-If the product is designed for use in a dishwasher and/or microwave oven, place it in a dishwasher and run the dishwasher for one cycle during the inspection period and also 10 minutes in the micro-wave oven.-S2 |
PASSED | |
Check capacity (volume) by weighing the item or by using a capacity gauge ( the mug, bowl and the container claimed with the volumn)-The results must conform with the specifications.-S2 | FAILED | |
Check if items stand properly when pieces are stacked up, if this test fail, please state the cause clearly on inspection report and take photos- 1)Stack the products (60 pieces for the plate/reference and 12 pieces for bowl/reference and cup/reference ); 2) Ensure they can stack properly and do not wobble or tilt over-S2 |
PASSED | |
Perform a fatigue test-On all adjustable parts. Do this 20 times.-S2 | PASSED | |
Perform a fitting test check-The lid should fit the base well.-II | FAILED | |
Test the strength of the handle.--S2 | FAILED | |
Test the fit of the lid. and lid can not falls off when the teapot is tilted toward 90 degrees-If the item has a lid - The lid should fit well.-S3 | PASSED | |
Perform a wobble test on a flat glass panel. Check both the top rim of the glass and the bottom.-There should be no wobbling of the base or the rim.-I | PASSED | |
Hand washing test -- --Wash the product with cotton fabric in cold water of room temperature (about 20--35degree) and hot water of tempertature (about 80 -- 90 degree) -- During washing, dip product into the water and wiping the whole surface of the product -No color should be removed from the item’s surface during the test and no printing, markings or paint should fade.-3 pcs | PASSED | |
Test the item for water leakage during the entire inspection period.-Fill the item with water then place onto a paper to check there is no leakage at all.-S2 | PASSED | |
Compare the inspection sample with the approval sample.-II | PASSED |
Chinaware QC check, Chinaware 3rd party QC check services, Chinaware third party QC check services, Chinaware QC check in China, Chinaware third party QC check, Chinaware QC check services, Chinaware 3rd party QC check, Chinaware third party QC check services in China, Chinaware third party QC check, Chinaware 3rd party QC check services in China, Chinaware third party QC check services, Chinaware 3rd party QC check in China, Chinaware QC check services in China, Chinaware 3rd party QC check, Chinaware third party QC check in China, Chinaware QC check services, Chinaware 3rd party QC check services
3rd party preshipment products goods factory onsite inline final Random AQL PSI TPI FRI DUPRO third party on-site in-line pre-shipment QA quality control assurance inspection services in China India Vietnam Thailand Malaysia Bangladesh Taiwan.